Ghost Controls Hinge & Roller Replacement Nationwide

Ghost Controls Hinge & Roller Replacement: The Las Vegas Owner’s Guide

Ghost Controls hinge and roller replacement in Las Vegas typically runs $145 – $285 installed, and yes, we stock the common Ghost Controls hinge and roller kits on our trucks so most swaps happen same-day. You’ll usually know the part has failed before you see it: the gate starts dragging on the ground, makes a grinding sound when it moves, or refuses to close all the way because the hinge has settled. In Las Vegas heat, powder-coated hinges and nylon rollers take a beating. Sun bakes the coating, dust gets into the bearing, and within a few summers you have metal-on-metal wear. Warden Gate Repair Las Vegas handles this repair several times a month, and it’s one of the more straightforward jobs we do. We’re an independent service provider, not affiliated with Ghost Controls, but we work on their equipment regularly.

Call (725) 529-9468

Which Ghost Controls Models This Applies To

This repair applies to nearly every Ghost Controls swing gate kit sold for residential use in Las Vegas: the TSS1, TDS2, AXS1, R20, and the older VS1 series all use the same basic hinge and roller design, but the bolt spacing and roller offset vary by gate weight and post style. Before ordering anything, check the hinge plate for a stamped number, usually a 4-digit code starting with 8 or 9. If the stamping is worn off, measure the bolt hole spacing center to center: most Ghost Controls residential hinges are 3-1/2″ or 4″ on center. Las Vegas installers sometimes mix in universal hinges from hardware stores when the original wears out, and that’s exactly where problems start: the offset isn’t right, the gate binds, and the opener motor burns out fighting the misalignment. We match OEM Ghost Controls hinges and rollers where the budget allows, but we also keep a quality aftermarket equivalent for the older discontinued models where Ghost Controls no longer supplies parts. The aftermarket pieces we use have sealed bearings instead of the open bearing on some original rollers, which matters in Las Vegas dust.

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

• The gate sags toward the latch side. The top hinge bushing has worn into an oval. The gate drops a half inch or more, and the latch post no longer lines up. This is the most common early warning sign on Ghost Controls gates in Las Vegas.
• You hear grinding or squealing when the gate opens. A roller bearing has gone dry or collapsed. The sound gets worse in summer because heat expands the housing and dust has already scored the bearing race.
• The gate shudders or hops halfway through its swing. The roller has a flat spot from sitting in one position for months. Homes where the gate stays open all day in Las Vegas see this more often because the roller never rotates.
• The opener runs but the gate moves in jerks. The hinge is binding, not the motor. The motor keeps pushing, the gate resists, and eventually the opener arm or the controller board pays the price.
• Rust streaks run down from the hinge pin. The original finish has failed and water has gotten inside. Once a Ghost Controls hinge starts rusting internally, replacement is the fix, not lubrication.

If you’re seeing any of these on a gate in Summerlin, Henderson, or Sunrise Manor, the repair is usually one truck visit. Call us at (725) 529-9468 and tell us what the gate is doing wrong. Cole Rafferty always says, “Tell me what it’s doing wrong, and I’ll tell you exactly what it costs to fix it.”

Replacement Cost & What’s Included

For a standard single swing gate with two Ghost Controls-style hinges and two rollers, expect $145 – $285 installed in Las Vegas. A heavier double gate with four hinges and four rollers typically lands between $260 – $410. The range depends on whether we’re replacing both hinges or just one, whether the gate post is still sound or needs a steel shim plate, and whether the gate itself needs realignment after the new hardware goes on. Every quote is written and given to you before any work starts. No surprise line items, no “we found something else while we were in there” invoice. The 365-Day Done Right Promise covers the parts and the labor in writing: if the hinge or roller fails within a year, the return visit is free.

DIY or Call Us?

The honest answer: you can do a visual check yourself. Put your hand on the gate and try to lift it. If it moves up more than a quarter inch, the hinge bushings are done. Look at the roller wheel. If it’s cracked, flat-spotted, or wobbles when you spin it, it’s done. What you should not do is unbolt a sagging gate and try to swap hinges yourself. A full-size Las Vegas steel gate weighs 200 to 400 pounds. When the last hinge bolt comes out, the gate is coming down, and it will take a hand or a foot with it. We also see gates wired with low-voltage cable running through the hinge post; cutting that by accident turns a $200 hinge repair into a $600 opener wiring job. If the gate is sagging, call Warden Gate Repair Las Vegas at (725) 529-9468. The estimate is free, the price is written before work starts, and you’ll know exactly who is coming to your door: name, photo, and credentials sent before the tech arrives. That’s our Threshold Standard, on every visit.

FAQs